This error occurs when the media is recognized in a completely abnormal way. The media sensor passes through the media container in front of the black rubber. Check if the media is literally dirty, if there is deformation at the control points of each of our media sensors, or if there is any stretched material at all. Check the media location.
* This is with An error message is displayed from major firmware version 1.40 or higher.
The paper may not be recognized, or the media configuration is in the wrong position. Do not load multimedia content where the side stand of the stand is in contact with the side plate on the right. Since the braces can tip over but can be lifted, they can break your head. It is recommended that the right edge of the media be aligned with the right edge of the pinch roller.
Mimaki Europe bv Stammerdijk 7E 1112 AA Diemen Netherlands t. + 31 (0) 20 462 seventy six 40 e. [email protected]
Failed to locate the media. This indicates that the media is out of range of the media sensor.
1. Reload the media into the sensor area and try again.
2. The media sensor runs over the dark rubber band of the roller and detects the difference between rubber and media. 1) Remove dust and dirt with some kind of black rubber. 2) Spread the material evenly. Surface changes can cause recognition problemsBy fishing. 3) Adjust the gap or adjust the position of the media to bypass the detection of the printed image data.
3. The position of the test bench. Media detection may not work if the edge of the media is too close to the coating station. The right start of the media should be aligned with the right edge of the small roll.
4. Sensor of a clean environment using natural tampons. Move the drive sled to the left next to the service station and clean the transducer with ethanol using a 100% organic cotton swab. Then dry the transducer with a new cotton swab.
Error MEDIA 50 DETECT for Mimaki JV33-160, how to fix it?
Fortect is the world's most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, Fortect quickly finds and fixes a broad range of Windows problems - from system instability and security issues to memory management and performance bottlenecks.
1. Download Fortect and install it on your computer
2. Launch the program and click "Scan"
3. Click "Repair" to fix any issues that are found
The Mimaki JV33 series are the most commonly used tools from Mimaki. We probably would have run into some problems while using it. This is where the serious error “50 MEDIA DETECT error” occurs, which many people have already answered. Let’s discuss how we can solve this.
This error occurs when advertisementsThe phenomena are not recognized normally. Here, I would say, are the solutions.
Step 1. First put the stand back in place. Then repeat step 2: discover
Step The TV and radio sensor moves along the black rubber in front of the media holder. Check to see if the media is dirty, too tall next to the media being passed over by the sensor, or if the media is pulled out.
Step 3 or more: Check the preset position on the media. Moving the media holder to the right from the specified position may result in an error. Fluid should never flow to the right of the corresponding right pinch roller.
Step 4. Perform [CR.Main maintenance] to successfully clear the media sensor. Method: Cleaning Gently wipe it with a cotton swab filled with ethanol for disinfection, then dry the goose down with a new cotton swab. (See Operating Instructions -> Maintenance -> Sealing Station Maintenance -> Cleaning the Ink Head and Environment.)
If you have a lot of welcome questions, do not hesitate to contactto us in addition to questions. We want to help you solve these problems.
This error is displayed if the media area cannot be recognized correctly.
For details on the steps, see also the “Operating Instructions” under “Notes on Media Setting” and “Specifying Large Roll Media”.
ã € Procedureã € ‘ 1. Make sure the roll tray is in the correct position for the ID of your own roll media. 2. Make sure your media is level. 3. Transparent advertising can trigger a message without blocking the light from your current sensor. 4. Check the right end of the storage devices for cuts (although this can be adjusted accordingly, this message may appear if the sensor light is not blocked). 5. Clean the storage device sensor.
