Solution For I386 / Asms Error

 

Approved: Fortect

1. Download Fortect and install it on your computer

2. Launch the program and click "Scan"

3. Click "Repair" to fix any issues that are found

Speed up your computer's performance now with this simple download.

You should check these troubleshooting methods if you encounter the i386 / asms error code on your computer.

 

 

I will open a new thread and sell your questions there. Have you just checked your RAM DIMM in Slot Machine 1 and how did you boot your operating system? You can go into BIOS and increase the memory voltage to the desired level, or adjust the memory voltage for mfg. Specifications. Memory is usually the cause of system errors when trying to run software, for example when installing another operating system. It happened to me.

Open support for MB on a concept album from another machine. Double click My Computer, you need to open the files from the MB CD and then share the Drivers folder. From there go to Sata folder and copy Sata folder from all zones to disk except GUI and readme file.

McAllen:

So the new system, the Intel DG33BU motherboard, works with SATA, but no RAID. Initially booted from the XP SP1 installation disk, for itThe installation became “Installing Devices”, then blue. Let’s say a few people, and obviously SP1 discounts might support my motherboard, so I had to buy myself a CD-SP2. Ok I have the SP2 cd, booted up, started most of the installation and I can’t even get to the SP1 cd, it says:

Fatal error:
One of the components required by Windows to proceed with the installation may not be installed

Now I have some kind of floppy drive, but what I don’t have is the SATA driver floppy disks. Why did XP SP1 survive and not SP2? Why did I break before? Where can I get SATA drivers for Mobo? You are not visiting the Intel Blog site; (
‘
To help?

# 1Strong

• 
• Members
• 5 posts
• OFFLINE

A

• Local time: 03:32

When I tried to boot Windows XP on a new machine (this is a legitimate copy of someone MSDN), I get this error after splitting and copying is complete, and it propagates to the installation: “Installation failed:” i386 asms need “I have never seen this error in several years of creating a new tool and reinstalling Windows. I would be grateful for any help and thanks for the “advance”!

BC AdBot (login To Remove)

# 2Monty007

• 
• Members
• 1,151 posts
• OFFLINE

A

• Male
• Location: Australia
• Local time: 21:02

Hello me robusto, I made this mistake about a year ago and it also turned out that the CD / ROM was about to come out, but usually the CD itself could be damaged.

# 3

Usasma

Still itemprop = “Creator for the visually impaired (Avatar is definitely a keepsake created by my father

• 
• BSOD Kernel Dump Expert
• 25,091 posts
• OFFLINE

A

• Male
• Location: Southeast Connecticut, USA
• Local time: 07:32

In most cases, as with Monty007 USA, this error is caused by a bad CD. Try cleaning your real hard drive gently to see if that helps.

My browser triggered a stream of traffic that blocked my IP address. I hope to be able to contact him soon. I will revisit this post again with that in mind as soon as I can.

– John (my website: http://www.carrona.org/ You) ** If you need a detailed explanation, ask. I have chic. If ** I have not responded within 48 hours, please contact me. Recently, my eye problems have increased and I cannot read messages. (Nov 23, 2017) For your information, I am about 30% completely blind in my right eye and in shadow in my left eye.

If eye health problems suddenly worsen, I will not be able to approach them. In case, in addition to the necessary assistance, please send the PM to an employee for help.

# 4Strong

• Topic start
• 
• Members
• 5 posts
• OFFLINE

A

• Local AM

haha, time: 03:32 thanks to all the family, yes, I used 3 new CDs to test this issue and it should still be a CD issue. A co-worker friend suggested a CD drive failure, but I found it incredibly odd as it was all happening in one file for all effort. I’ll try a new disk and see how it works.

UPDATE: Guess someone didn’t work = / I had a SATA CD-ROM drive, then took it out and put it working. Perhaps the CD-ROM drive of the computer I used to burn the Windows ISO is indeed damaged. I will try to create a new CD found on another computer. Anyone have any suggestions? I checked the CD I was using and therefore it contains i386 asms in the following folders:

# 5Usasma

Still disabled with confidence (Avatar is a requestthen my father’s developed memory

• 
• BSOD Kernel Dump Expert
• 25,091 posts
• OFFLINE

A

• Male
• Location: Southeast Connecticut, USA
• Local time: 07:32

Are you feeding an old CD to make modern copies? If so, the file may be corrupted again, so this particular error will be copied as well. Can you use a different hard drive?

Sometimes you can copy the entire hard drive to your hard drive and set up a race from there – it might be worth trying.

Didn’t the installation make it to IDE and SATA drives?

My browser triggered a stream of traffic and my own IP was blocked. Hopefully this will be fixed soon. I will post a positive review again as soon as I can.

– John (my website: http://www.carrona.org/ You) ** If you need more explanation, ask. I have chic. If ** I have not responded within 48 hours, please contact me. (Nov 23, 2017) FYI – I really chuI imagine myself completely blind on the right side by about 30% and blind in the left eye.

If some vision problems suddenly get worse, I will not be able to answer. If this is the case and you need help, ask one of the staff for help.

# 6

Strong

• Topic start
• 
• Members
• 5 posts
• OFFLINE

A

• Local time: 03:32

I made a new CD somewhere from our MSDN subscription. Today I will try to make a new CD on my computer for creativity. Perhaps my ISO was damaged or my CD burner is broken. I only have SATA hard drives and one of the newer Seagate shaped areas that are really thin.

 

 

Speed up your computer's performance now with this simple download.