The Easiest Way To Troubleshoot Mintek DVDs

Over the past few days, some of our users have informed us that they have encountered problems troubleshooting Mintek DVDs.

Approved: Fortect

1. Download Fortect and install it on your computer

2. Launch the program and click "Scan"

3. Click "Repair" to fix any issues that are found

Speed up your computer's performance now with this simple download.

• Be careful not to drop your device

Note: when the device will be tested Get rid of for a long period of time

* 1. Press this SOURCE button to switch between DVD, AV OUT and AV IN.

l. Connect the power adapter to the DC power outlet of the device.

2. Insert one end of the person’s power cord into the elevator input adapter and the other end into

Home store. During this time, the canning machine works normally.

Note. Turn on the device before removing the AC card from the device so that the device does not turn off

… Turn off the machine and other devices.

… Hold the plug to disconnect the cable, do not pull on the cable.

1st mini-jack: – Connect to the AV OUT jack of the device.

3. Red plug: Connect to the AUDIO IN R jack on the TV.

4. White plug: Connect the AUDIO IN L jack of the TV to.

l, mini jack: – can be connected to the AV OUT jack of the device.

3. Red plug: Connect the LINE IN R jack of the amplifier.

4, white – plug: Connect to the continuous LINE L socket of the amplifier.

1. Look at the plan, the battery compartment of some remote controls is open

2. To usethe remote control, point it at the remote control sensor at

3. Usually, lk_r energy is enough for about a year. Replace the battery if

4. Remove the batteries if the remote control will not be used for a long time.

• The detections shown in the following table are provided in the manual.

5.If ​​the device is connected to a TV or amplifier, set

Adjust the volume according to the TV operating instructions in AV mode.

2. Holding the edge of the disc, place it in the notched center

1. If you are. you definitely feel bright. … fits. during playback. press .MONITOR. button. to select .light.

Adjust and press .._ _ buttons until moderate light is available.

2. If you feel an unacceptable color during playback, press the MONITOR button to select a color setting.

and content buttons _ or _ until a moderate color is publicly available.

3. Press the MONITOR button to select the presentation mode and press the button ki., Q or _ to choose:

Note. Light spots and dark spots may appear on the TFT LCD during playback, which is normal

• You must double click on this option

3. Press the buttons frequently • to move to the next, or

(similar to CD tracks). If you can skip this, there will be

3. Press the • or T button to move to the next, or

. receive

3. Projector buttons – or – for scrolling support

3. Press the â € or â € button to scroll

2. Press direction button (or â €) to select

• Press the arrow buttons (or â) to highlight

This is the Land-R signal output mode

Use the reverb mode you want to use to make your decision.

• You can enter the elapsed chance of the disc

… You can mark the elapsed time of the melody

• You can access the track that someone wants to play by typing it

A disk that can be quickly accessed. You can wake up

3. Press _1, â € ¢, I ‘, c, – to enlarge

This guide is intendedThis is for your information only. Any changes made to you and specifications will not be reflected.

This product contains copyright protection technology, which is usually protected by method formulas

. protected

Certain US patents and intellectual property rights owned by Macrovision Corporation

Others and Beneficiaries. Use of this copyright protection technology must be approved

. be registered

Macrovision Corporation and is intended for home use and other limited display purposes only if

Please follow the explanations below to properly install the battery. Make sure the battery

Correction for using the player. Otherwise, each battery may disconnect and

Disconnect the AC adapter and power cord from the player first, then attach the kit.

3. Insert the battery tabs into the corresponding holes on the player. Then slide this battery until

Note. Remove the battery from the player after using the player.

1. В Turn off the player. The battery can only be charged when all players are powered off.

3. Connect the AC adapter and power cord for the time required for the player. The download process will start and

The POWER / CHG indicator lights up in orange. When the charging process is set, the display turns off:

1) Do not unplug the main power supply and power cord during overdubbing while

POWEPJCHG display turns off: Battery charging time is approximately 4.5 hours and

2) Be aware of this or the operation of the player if the connected battery may become hot during charging. This is definitely a mistake.

3) The battery indicator appears on the screen when the battery is almost empty.

2. Disconnect the AC adapter and power cord from the player.

4. Slide the miscellaneous packaging lock switch in the open direction, if so, slide the reader in the correct direction

In general, the continuous operation time after charging the battery is as if it were on the fly. For

When operating on battery power, the ambient temperature must be between 5 ° C (41 ° F) and 35 ° C (95 ° F).

A newly purchased battery can only be used after it has been charged. Required

until the battery’s longest indicator light comes on, then charge it to a temperature lower than or near internal temperature.

Do not neglect the battery, seek service from a qualified technician.

1. Connect the DVD system (DC OUT) to the TV tuner (DC IN) with the power cable.

2. Connect all DVD players (AV IN) to a TV tuner (AV OUT) with an AV audio cable.

3. Connect the antenna from the connector on a working antenna or cable / satellite box to the antenna input

Speed up your computer's performance now with this simple download.