Approved: Fortect
In this guide, we are going to find out some of the possible causes that can lead to the mp530 ink validation error, and then I will provide possible fixes that you can try to fix the problem.
To remove the back seat and ink type and print head from yourFor the great PIXMA MP530, please follow the points below.
- Make sure the printer is on and press the
button. (The paper output tray opens.) Note. If the scanning unit (printer cover) is inserted for more than ten minutes, the print head will move to the right. In this case, close the corresponding scan unit (printer cover) and reopen who’s.
- Open the inner cover.
- Remove the ink tanks by pressing the button. Press and touch each container with your fingers.
Caution. When you finish handling ink containers, handle with care to avoid staining your clothing and the environment. Be sure to remove the ink tanks one by one.
- Raise the printhead lock lever.
- Tilt the printhead slightly towards the front device and lift it up carefully.
Caution: Do not touch printhead <1>: electrical <2> nozzles, ink contacts or <3> connectors. This may cause printing problems.
- Place the printhead into the printhead holder and gently lower the printhead latch knob until you hear a click.
- Insert the printer reservoirs into the printhead.
- Press firmly on the
seal on the ink bottle, you will finally hear a click … 
- Â Make sure all ink tanks are installed correctly and that the ink tank lights are on.red.
<7> The ink tanks are usually installed correctly.
<8> Ink tanks are not always installed correctly.Note: Â Click here to light up the summer ink lamps.
- Â Close the inner cover and drive cover) (Dr. uker.
Caution: when closing the reader (printer cover), be careful not to get your fingers caught.
NOTE: The next printing process starts with cleaning the print head. Printing starts with autopilot.
If a typical error is not resolved after removing and reinstalling the ink tanks and printhead in the printer, you may need service to fix the problem. Please click on the Contact Us website below to view service options.
Is this the answer to your question? or For more help, see the Contact Us section.
answered your individual question? Click the Accept as Solution button so others can find a new answer as well.
An Error Message Appears On The LCD Screen
1) ON / OFF button: to start and stop the machine.
2) OK button: to delete and restore all errors. For some operator request errors, this error is automatically cleared if
The cause of the error has been fixed and it may not be necessary to press the OK button multiple times.
3) Stop / Clear Button: To cancel the job when an error occurs and to clear some errors.
| INK U041 CHECK | Ink was operating normally (ink capacity light is blinking). Replace the ink tank and close the scanning unit (printer cover). If the canvas is printing and you want to help continue printing, no doubt click [OK] with the ink tank installed. Then, the printing shown below can resume the low-ink condition. Replace any empty ink tank immediately after printing. The product may be damaged when used outdoors.
Note. If multiple ink lights are on redWell, check the speed at which they are blinking. Blinking quickly (about one second is interval) ink is out. Slow blinking (every 3 seconds) means ink is nearly empty. |
| CHECK INK U071 Reasons u072 | are possible as follows:
– Some ink tanks are not attached. – Often several ink cartridges of the same color are installed. Make sure the cartridges are installed in the correct position. |
| INK U130 CHECK | An empty ink cartridge is still inserted. Change ink
Printing may damage the printhead. Canon is not responsible for equipment malfunctions that may result from filling up the ink tanks. If we want to continue installing the toner cartridge, hold down the new [Stop / Reset] button for at least 5 seconds and then release it. When used with full tanks, ink will be stored accurately. * This operation provides a function to determine the remaining free ink level. |
| CHECK INK U140 U043 | Possible reasons are as follows:
– The printer’s ink tank may not be installed correctly). Install the appropriate ink tank . – The ink bottle may not be compatible with this unit (Tattoo bottle light is off). Install the appropriate tattoo reservoir. |
| CHECK INK U150 | An ink reservoir error has occurred (ink reservoir light is still off). Replace the ink tank. |
| CHECK PAGE SIZE | The page size in the ADF or cassette and the specified page size were different.
Load or resize the page correctly, this option is for page size. Then click [OK]. |
| CHECK PRINTER | An error may have occurred that requires service.
Power on Turn off the device and unplug the device’s power cord from the power source. After a while, reconnect the machine’s power cord and plug it back into the machine. If exactly there was an erroribca, please contact customer service . |
| PKD. CLEAR. STOP [ok] DOC CLR [STOP] |
Documents remain in ADF. Click [OK] to delete the documents and click [Stop / Reset] to stop retrieving. To continue scanning, launch the application. Scanning from the ADF may not be supported depending on the software. Contact the manufacturer of the app for more information.
 pla Fortect is the world's most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, Fortect quickly finds and fixes a broad range of Windows problems - from system instability and security issues to memory management and performance bottlenecks.
Speed up your computer's performance now with this simple download. If your favorite Canon printer does not detect a compatible tattoo cartridge, it could be because the cartridge chip reports were buffered empty before being processed. Press and hold the Stop / Cancel buttons for 5 seconds to bypass the Out of Ink message and your container should work.
Why is your printer getting this error message? Since the remanufactured ink cartridge uses the original cartridge chip, the printer computer will mark the ink level that matches the memory of the used chip if the cartridge origin d has been realized and used in the printer.
Disconnect the AC adapter and associated USB cables from the printer.Open the capsule door, press and hold the intensity button.Reconnect the power cords while continuing to hold the power button.Close the cartridge door and release the power switch. The ink toner cartridge has been discarded.
 Related Posts: |
