This article describes the steps to set up printing on a clustered server.
Additional Information
You should definitely use Windows Clustering to host the recording server functionality. The configuration steps with Windows Microsoft Server 2003 are different from the steps with Windows Microsoft NT Server 4.0, Enterprise Microsoft Edition, Windows 2000 Advanced Server, and Microsoft Windows 2000 Datacenter Server to take the spooler resource in the Cluster Administrator and then connect to a much larger server to configure ports and print queues.This is an improvement over previous versions of Windows clustering, which required users to repeat the configuration steps for each node in the cluster.
How To Change The Print Spooler Resource For A Cluster
The first step in configuring a clustered watermark server is to create a print spooler pool to serve on the clustered Internet. To make the print spooler service available, you must select the appropriate resources. To do this, create a spooler in the resource cluster administration:
To open Cluster Administrator, click Start, select Run, type cluadmin and click OK.
Right-click in the left pane and select Configure Application.
Click Next on the Welcome screen, and then click Next again to prepare a new virtual server.
Click Use Existing Resource Group, then click an available group that recently had a disk resource where you want to store all print spoolers.ati and printer drivers. Click Next.
Enter a name as the source of the information group, a name that correctly represents the group, for example “SPOOLER”.
Note
This appointment is of an administrative nature only in the cluster administration.
On the virtual server access information screen:
In the Network Name field, enter the NetBIOS name to which clients will connect. This is the name of your current NetBIOS virtual server as assigned by clients accessing printers: virtual server printer
Note
Microsoft offers 8.3 naming convention compliance through backward compatibility with the core client.
Enter the IP address that clients will contact to connect to this virtual printer. If the cluster nodes are suffering from installed and connected Unix print services, clients can connect to a line printer outside of this IP address (lpr).
Click Next.
Typically you can use the Advanced Properties screen to make changes I into the resources you want to create, and then click Next.
On the “Create resource for my application” screen that opens, click “Next”.
Click Print Spooler, then click Next.
Give the spooler a name for the resource.
Note
This reputation is used for administrative purposes only when administering the cluster.
Specify the print spooler resource for dependencies:
Click Advanced Properties and click Modify to view the cost of the dependency.
Double-click on the physical disk resource where you want to find the print spooler files and the webpage you just created with a network name.
Fortect is the world's most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, Fortect quickly finds and fixes a broad range of Windows problems - from system instability and security issues to memory management and performance bottlenecks.
1. Download Fortect and install it on your computer
2. Launch the program and click "Scan"
3. Click "Repair" to fix any issues that are found
Check configuration and test failover:
Right-click the print spooler and group, in this case click Connect.
Make sure all resources are online byWe check the Firewood event for errors.
Right-click the print spooler group, select Move Group, move the print spooler resource to every single node in the cluster that it can own, and then verify that all resources connected to the network are switched.
Note
If you are configuring an active / active print server, you must create a group for each node and assign a different preferred owner for each print spooler collection. You cannot have multiple spooler resources in the same group. When you configure an active / active print server, multiple nodes in the cluster perform print jobs for clients with multiple print spoolers. This can include two to four nodes that are actively processing requests.
If a single site hosts an array of print groups, you can use spoolers to find all printers in almost all groups.
How To Create A Printer To Be Placedto The Queue
Now that you have correctly configured the print spooler resource with some required resources, you can create all print queues for all physical printers. You can usually also use the Resource Kit Clustool utility to migrate pre-existing Internet print queues to a clustered server. After this number, use the Print Migrate utility to update the printer driver. For best results, avoid setting up multiple servers to communicate immediately with the same printer.
From one of the specific nodes, or from a remote computer that may have administrative privileges in the cluster, click Start, select Run, type VirtualServer, where VirtualServer is probably the name given to our network. the name resource on which the print spooler resource depends.
Double-click the Printers folder.
Double-click Add Printer to open the Add Printer Wizard, then click Next.
Select Create New Port and click Next.
Note
TCP / IP ports are usually the only ports supported for almost all Windows clusters. Use the Standard TCP / IP Port option if the print clients do not require RFC-compliant LPR ports. In this case, do the following:
Check the panel, double-click Add or Remove Programs, then click Add or Remove Windows Components to start the Windows Components Wizard.
Click down in the Components section and click to select the entire scan area for other network files and print services.
Click Details to open the Other Network Files and Print Services window, select the Print Services for UNIX to display check box, then click OK to open the Other Network Files and Print Services window. “Next
click here to continue with the Windows Components Wizard.
When the wizard completes, your current LPR port will be available as an absolute port type. By default, LPR uses only 11 TCP ports as per RFC 1179.
Enter the IP address of the web printer that should handle our jobs It can be printed, in the name of the printer, or possibly in the IP address of the box.
Note
Bidirectional printing can also be problematic with LPR printing. Some printer drivers enable this option, changing the default settings. If you are creating an lpr port and / or printer, disable it
Print servers can be used. to enforce administrative regulations such as print quotas for color materials, user / service authentication, or watermarking documents.
Active / Active Print Server Configuration – This is a configuration in which there are undoubtedly several nodes in the cluster that typically process print jobs for clients with a set of print spoolers. This can include two to four nodes processing requests.
A typical print server sends print requests to multiple computers and computer printers over a network. For example, a user of a large networked workstation sends a print command, which, according to an expert, includes a print file and information about the printer, which will be used, usually by a nearby printer for convenience.
