What is the Win32 error code for Winock?

Winsock error code: 10060, Win32 error code: 10060, Target domain: gmail.com, Error message: The connection attempt failed because each of our connected sides did not respond correctly after a while, or the attachment that was configured did not succeeded because the connected host could not guarantee that you wrote the answer IP: 25 .

What Is Winsock Error Code 10065 And How To Fix It?

Posted on November 12, 2021November 13, 2021 by Brian Magallanes

Table of Contents

Approved: Fortect

1. Download Fortect and install it on your computer

2. Launch the program and click "Scan"

3. Click "Repair" to fix any issues that are found

Speed up your computer's performance now with this simple download.

Here are some simple methods that can help you fix the problem with Winsock error code 10065. Extension socket error 10060 is a winsock error usually caused by outgoing connection problems or connection health problems on the host side. Outbound connections are most likely affected by the presence of firewall or anti-virus software on an electronic or local network connection.

Socket Errors 10061, 10060, 10064, 10065

An output error of about 10060 is probably a Winsock error. This usually happens due to outbound connectivity issues or host-side web connectivity issues.

Outgoing connections can certainly be affected by the presence of antivirus software or software on the local computer or networkunification. Both can block their ports, which are needed to establish an interesting FTP connection to the remote server. For a real regular FTP session, disable your firewall or antivirus software, or configure them under Allow CuteFTP to set up an FTP training session on 20 ports and 21 software products for potential customers. Typically, the manufacturer of the device software also has specific instructions that can be purchased from their website. If you still get the same error, make sure shortly after opening ports 20 and 21, contact the administrator of the site you are trying to connect to.

10060 is a basic connection timeout error that usually occurs when a potential client does not receive a response from your server to a specific command. This error often occurs when trying to PASV URL to the server preferred by this PORT for data connections. If users see an error log similar to the one below, click Enter Results in theProperties of the problem site, and then change the type of data connection you can use for the PORT.

If you still get a solid 10060 error, the server may be trying to send the list directly to a directory (with several thousand files) that is waiting for the client to timeout. Try increasing the timeout value in the Global Options dialog (Tools> Global Options> Transfer> Reconnect and continue for [n] if nothing was suggested for seconds) to a higher value, such as 45 or 60 seconds.

The connection is interrupted or due to an error timeout.
Check if the destination IP address of the recipient is correct.
Generally, increase the connection timeout threshold under General Settings> Connection.
Approved: Fortect

Fortect is the world's most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, Fortect quickly finds and fixes a broad range of Windows problems - from system instability and security issues to memory management and performance bottlenecks.
1. Download Fortect and install it on your computer
2. Launch the program and click "Scan"
3. Click "Repair" to fix any issues that are found

Switch to the opposite data connection form (PASV or PORT) in the Site> Parameter Type tab.

When trying to connect to a commercial server, make sure it’s not a small town.

If the server name was used, persuadeMake sure it matches the correct address.

If you are using a local server table to resolve server headers, make sure you do not need to convert it to a legacy address.

Try pinging all addresses. (For more information, see Troubleshooting Tips.)

If customers are using a router, make sure it works (test it by pinging and then pinging an address outside the router’s home).

Trace the route to the destination to ensure that all routers along the link along the path are operational. (For more information, see Troubleshooting Tips.)

Make sure your subnet is configured correctly.

10061 is a “Connection refused” error message sent to you by the server. You could not log in because our target computer was actively refusing to do so. The most common reason is a misconfigured site, a full server, or notthe correct port as specified on the client.

Open the site. Then the manager decides to go to the site.
Go to main menu> File properties.
Click the Type tab.
Enter the correct port number in the Port field.

Sometimes error 10061 is caused by firewall or antivirus software on the entire local computer or network connection. Both can block the ports required for a successful FTP connection to the server.

For a regular FTP session, turn off your firewall, antivirus, or utility to configure it so that CuteFTP detects an FTP session on both ports 20 and 21. See the documentation or dump file for your specific firewall or antivirus. Software for instructions. Usually the manufacturer of our device or software provides instructions on their website.

If you still get a single error after opening ports 20 and 21, contact the administrator of the entire site you are trying to connect to.

The remote host actively rejected the connection attempt.
Make sure the target forum name or IP address is correct
Carefully check which port number is valid (under Site Settings> Type tab).
The remote computer may be temporarily or permanently unavailable (please try again later).
Make sure you have selected the correct protocol (SSH2, SSL, FTP, etc.) and that you have configured all the necessary parameters for which protocol.
Make sure the destination IP address and port numbers are correct.
The remote server may well reject multiple connections from the corresponding client. Try using a single wire when connecting to a specific computer (Site Settings> Options).
Try pinging an address.
If you are actually using a router, make sure the switch is working and (just test it and then echo to an address outside the router).
Trace your route to your actual destination to make sure all routers connected to the Internet are up and runningui.
Make sure the subnet mask is configured correctly.